Portable Material Lift, 200 kg, 4.5 m ReachSKU: TMB-PM200-405700817
A single mast that folds down to 1.33 m and reaches 4.5 m — for canopies, duct runs and panels that are too awkward to hand up a ladder, on a base frame that stands on its own.
- ✓
Held in stock in the standard 200 kg, 4.5 m build and dispatched from our own warehouse. A different top, reach or colour is built to order — see custom options.
- ✓
Built to the specification published here — same mast, winch and base frame on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
A hoist that travels like a ladder
For the jobs where the material is too heavy to hand up and there is nothing to fix a lift to: the machine goes in the van, stands on its own base, and puts the load at 4.5 m without scaffolding or a second pair of hands.
4.5 m of reach from a 1.33 m package
The mast telescopes from a single square section, so the machine travels at 1.33 m — the length of a step ladder — and still puts a load at 4.5 m. One machine covers the first floor, the canopy line and the ceiling void.
Flat plate or padded U cradle
The top is interchangeable. A flat steel plate takes a box, a unit or a bucket; the U-shaped cradle has padded arms so a pipe, a duct section or a panel sits in it without being strapped. Tell us which you need and it is fitted at the factory.
Winch at the foot, ropes up the mast
The electric winch sits on the base frame with the motor and the rope drum at floor level, and four falls of steel wire rope run up the mast to the top. Nothing heavy is up in the air, and everything you would service is at the bottom.
Pendant control on a cable
The hand control hangs on a cable from the mast, so the operator stands at the base while the load goes up and can watch both ends of the lift at once. Release the button and the load stops where it is.
Portable material lift: technical data
Figures are for the standard build. The drawing below shows the 1.33 m stowed height and the 60 × 60 cm base frame — the reach is measured from the base frame to the top of the mast.
Lifting & control
| Lifting mechanism | Electric winch at the foot of the mast, four falls of steel wire rope to the top |
| Drive | Copper-wound electric motor with the rope drum on the base frame |
| Max reach | 4.5 m |
| Control | Hand pendant on a cable — up and down, load stops when released |
| Rope | 4 × steel wire rope |
| Mast | Single square steel mast, telescoping sections |
Build
| Load capacity | 200 kg |
| Stowed height | 1.33 m |
| Base frame | 60 × 60 cm |
| Top | Flat steel plate or padded U cradle, fitted at the factory |
| Stability | Four-corner base frame with two folding braces at the foot |
| Finish | Orange-red mast and base frame, red winch cover |
| Power supply | Confirmed per destination on the quotation drawing |
| Installation | Free-standing on its own base — no fixing to the building |

Manually measured dimensions may vary slightly; refer to the actual machine. Reach, top type and power supply for a specific build are confirmed on the quotation drawing.
One mast, a winch at the foot, a top that suits the load
The winch does the pulling from the ground, four ropes share the load up the mast, and the top is chosen for what you carry — a flat plate for boxes and units, a padded cradle for pipes and panels.

The winch sits on the ground
Motor, drum and rope all sit on the base frame at floor level, so the weight that does the lifting is never up in the air. The drum is inside a red guard, the motor is the copper-wound type used for site work, and the two braces run out to the corners of the frame before anything goes up.
Four falls, not one
Four runs of steel wire rope go up the mast to the moving top, so the load is shared and the top is held at four points instead of one. A single rope would let a plate tilt; four keep it level when the load is off centre.

Flat plate or padded U cradle
The flat steel plate is the general-purpose top — a box, an air-conditioning unit, a bucket of tools. The U cradle has two padded arms that hold a pipe, a duct section or a panel upright in the middle, so it can be offered up to a fixing without being tied on.
Padded arms, so the edge is not marked
The cradle arms are wrapped in soft padding. A pipe sits in the curve, a panel or a duct section leans against the arms, and the padding takes the contact instead of a painted edge on bare steel — the load is held upright in the middle of the plate rather than balanced on a corner.
Canopies, ductwork, panels — the jobs between a ladder and a scaffold
The lift fills the gap where a load is too heavy for two men on a ladder and too small to justify a scaffold: one machine, one operator, and the material arrives at height already level.
- Canopies and awning framesThe flat plate goes under a canopy frame or a polycarbonate sheet and holds it at the fixing line while it is bolted, instead of two men holding it up on ladders.
- Duct and HVAC installationA duct section sits in the U cradle and is raised to the hanger line, where it stays while the rods are set. The same lift takes the indoor unit of a split system up to its bracket.
- Panels, glass and signageA panel or a sign is carried upright in the padded cradle at the height it is fixed — no tilting it through a ladder opening, and no chipping the edge on the rungs.
- Ceilings and service runsCable tray, light fittings and ceiling tiles go up in a box on the flat plate, so the fitter keeps both hands for the fixing rather than one for the load.
Custom options on this material lift
The 200 kg machine with 4.5 m of reach is the standard build. The top, the finish and the reach are the parts customers change.

- TopFlat steel plate or the padded U cradle are both standard. A cradle sized to your pipe or duct section, or a plate with a lip to stop a box sliding, is built to order — send the dimensions of what you lift.
- Reach4.5 m is standard. A different mast length is built for a specific job — tell us the height you have to work at and where the machine stands, and we confirm the reach on a drawing.
- FinishOrange-red mast and base frame with a red winch cover as standard. Other colours are confirmed when you order, and your logo can be applied before the machine leaves the factory.
- Power supplyThe motor is wound for the voltage and frequency at your destination and stated on the quotation drawing — send us the site voltage so the machine arrives ready to plug in.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this one packs down to a single long crate, which keeps the shipping cost low.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How high does it lift?
How much can it carry?
Does it fit in a van?
What holds the load at the top?
What power supply does it need?
Can it be used outdoors?
Can a person ride on it?
What does it cost, and how is freight worked out?
For portable ladders and material handling on site, see OSHA 29 CFR 1926.1053 on ladders and 1926.501 on fall protection.










Reviews
There are no reviews yet.