Professional Lifting Equipment Manufacturer

Portable Canopy Lift, 200 kg, 4.5 m

TMB-PC200-405740245

Portable electric lift for canopy, awning and carport installation. A single telescoping mast carries a flat black steel tray at the top, load capacity 200 kg, maximum reach 4.5 m, stowed height 1.33 m, base frame 60 × 60 cm. The electric winch with a copper motor sits on the base frame and four falls of steel wire rope run up the mast.

Home/Mast Lift/Portable Canopy Lift, 200 kg, 4.5 m
In stock · ready to ship

Portable Canopy Lift, 200 kg, 4.5 mSKU: TMB-PC200-405740245

A flat black tray on a single mast: set the canopy frame on it, wind it up to the fixing line, and both your hands are free for the drill instead of holding the frame.

Load capacity
200 kg
Max reach
4.5 m
Top
Flat tray, 1.33 m stowed
Base frame
60 × 60 cm
Price on request
Standard build · 200 kg, 4.5 m reach, flat tray — unit price quoted with freight
Freight is quoted separately. Send us your destination port and the quantity — you get the machine price and the shipping cost in one reply, so you can compare landed cost. See Shipping & Delivery for how it works.
Request a quote
  • ✓
    Held in stock in the standard 200 kg, 4.5 m build with the flat tray and dispatched from our own warehouse. A different top, reach or colour is built to order — see custom options.
  • ✓
    Built to the specification published here — same mast, winch and base frame on every unit we ship.
  • ✓
    Nothing ships until you approve the freight quote in writing.
  • ✓
    Packing list, commercial invoice and bill of lading sent with every shipment.
Why this model

A third hand at the fixing line

Canopy and awning work is mostly one person holding the section up and another drilling. This machine takes the holding: the frame sits on the tray, the tray goes to height, and the fixing is done with two free hands.

01

A flat tray, not a hook

The top is a flat black steel tray with a rim, so a canopy frame, an awning section, an air-conditioning unit or a box sits on it and stays put. Nothing has to be slung or strapped, and the load comes off the same way it went on.

02

4.5 m of reach, 1.33 m in the van

The mast telescopes down to 1.33 m, which is the length of a step ladder, and still puts the tray at 4.5 m. It goes in the back of a van with the rest of the kit and stands up on site in the time it takes to fold the braces out.

03

Winch and motor on the base frame

The electric winch, the copper-wound motor and the rope drum all sit at floor level, and four falls of steel wire rope run up the mast to the tray. The heavy part never leaves the ground, and the part you would service is the part you can reach.

04

Pendant control, operator at the base

The hand control hangs on a cable, so the person working the lift stands at the foot of the mast with a clear view of the load and the fixing line. Let go of the button and the tray holds where it is.

Specifications

Portable canopy lift: technical data

Figures are for the standard build. The drawing below is measured with the mast down — 1.33 m to the underside of the tray, on a 60 × 60 cm base frame. Reach is measured from the base frame.

Lifting & reach

Lifting mechanism Electric winch on the base frame, four falls of steel wire rope to the tray
Max reach 4.5 m from the base frame
Stowed height 1.33 m to the underside of the tray
Mast Single square steel mast, telescoping sections
Rope 4 × steel wire rope, load shared at four points

Top, base & power

Top Flat black steel tray with a rim, bolted to the mast head
Load capacity 200 kg
Base frame 60 × 60 cm, two folding braces to the corners
Drive Copper-wound electric motor and rope drum on the base frame
Control Hand pendant on a cable — up and down
Finish Orange-red mast and base frame, red winch cover, black tray
Power supply Confirmed per destination on the quotation drawing
Installation Free-standing on its own base — nothing to fix to the building
Dimension drawing of the portable canopy lift marked 133 cm stowed height and a 60 × 60 cm base frame
Dimensions: 133 cm from the ground to the underside of the tray with the mast down, on a 60 × 60 cm base frame. With the mast extended the tray reaches 4.5 m above the base frame.
Built to order on this model The tray, the reach and the finish are the parts customers change. The flat tray is standard; a U-shaped cradle with padded arms is the other option on this mast, and it suits pipe, duct and panels better than a flat top. Tell us what the machine has to hold and at what height.

Manually measured dimensions may vary slightly; refer to the actual machine. Reach, top type and power supply for a specific build are confirmed on the quotation drawing.

Build detail

Tray at the top, winch at the bottom

Everything that carries load is either on the base frame or bolted to the mast head: the tray is a flat top you can set things on, and the winch that lifts it never leaves the ground.

Flat black steel tray with a raised rim on top of the canopy lift mast
Top

Flat, with a rim to stop a slide

Tray

The tray is a flat steel top with a raised rim all round, bolted to the mast head. A frame, a unit or a box put on it stays where it is put, and the rim catches the load if it shifts as the mast starts to move.

Use

Set it, wind it up, fix it

Sequence

Load the tray at the bottom where you can reach it, raise it to the fixing line, bolt the section, lower the tray and load the next one. The machine stays where it is for the whole run instead of being moved for every piece.

Electric winch, copper motor and red rope drum on the corner base frame of the canopy lift
Base

Four corners, two braces

Stability

The base is a 60 × 60 cm square frame that stands on the ground with two braces from the mast out to the corners. Fold the braces out on firm level ground and the machine is ready — nothing to bolt down, which is what keeps it portable.

Drive

Winch and drum at ground level

Winch

Motor, drum and rope sit on the frame at the foot of the mast, inside a red guard. Four falls of rope go up to the tray, so the load is shared at four points and the tray stays level even when the frame is set down off centre.

Where it is used

Canopies, carports and awnings — the frame that is too big to hold

A canopy section is light enough for one man to carry and awkward enough that two are needed to fit it. Put it on the tray and one man can do the fixing, at the height it is going to stay.

  • Canopy and carport framesAn arched or flat canopy frame is assembled on the ground, set on the tray, raised to the wall plate and bolted while it is held level — no scaffold deck, no two men on ladders.
  • Awnings and entrance canopiesAn awning section or a polycarbonate sheet is offered up to the fixing line at the right height and angle, and stays there while the brackets are drilled and set.
  • Signage and light boxesA sign panel is set on the tray and raised to the fascia, where it is fixed without being held up by hand against the wall.
  • Rooftop plant and unitsOutdoor units, vents and duct sections go up the outside of a building on the tray, on a machine that stands on the roof or the slab rather than needing a crane.
  • Canopy
  • Carport
  • Awning
  • Signage
  • Rooftop plant
  • Fascia
Built to order

Custom options on this canopy lift

The 200 kg machine with 4.5 m of reach and the flat tray is the standard build. The top, the reach and the finish are the parts customers change.

Canopy lift holding a steel canopy frame on a rooftop
Standard build shown: 200 kg, 4.5 m reach, 1.33 m stowed, 60 × 60 cm base frame, flat tray. A padded U cradle can be fitted instead for pipe, duct and panels.
  • TopThe flat tray is standard. A U-shaped cradle with padded arms is the other option on the same mast — better for pipe, duct and panels, which need to stand upright rather than lie flat.
  • Reach4.5 m is standard. A different mast length is built for a specific job — tell us the fixing height you work at and where the machine will stand.
  • FinishOrange-red mast and base frame with a red winch cover as standard. Other colours are confirmed when you order, and your logo can be applied before the machine leaves the factory.
  • Power supplyThe motor is wound for the voltage and frequency at your destination — send the site voltage and it is stated on the quotation drawing.
How a built-to-order unit is confirmed Send what the machine has to hold, the fixing height, the ground it will stand on and the site voltage. We confirm the top, the reach, the finish and the motor on a drawing before production starts.
Shipping & delivery

Freight is quoted separately and confirmed before dispatch

We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this one packs down to a single long crate, which keeps the shipping cost low.

  1. You place the order online

    Your order is recorded and the machine is reserved for you while the freight is quoted.

  2. We send a freight quote in 24–48 hours

    Priced to your nearest port, with transit time, or to your door as DDP if you prefer.

  3. You confirm and pay the freight

    One invoice for the shipping cost. Nothing is dispatched until you approve it.

  4. We book, load and send documents

    Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.

Why we do not charge freight at checkout LCL and FCL rates change weekly and depend on the port, the total volume and whether you combine this lift with other machines. A fixed online rate would either overcharge you or force us to invoice the difference afterwards — so we quote it properly instead.
What the freight quote includes Cost to your port or door, the shipping line and transit time, the earliest departure we can make, and the documents that travel with the goods. The mast packs down, so several units fit in one crate — tell us the quantity and we price them together.
Questions buyers ask

Frequently asked questions

What is the difference between this and the U cradle version?
The top. This one carries a flat black steel tray with a rim, which suits a canopy frame, an awning section, a unit or a box — anything with a flat base that can be set down. The U cradle has two padded arms and holds pipe, duct and panels upright. Both are the same mast, winch and base frame, and the top is fitted at the factory.
How high does it reach?
4.5 m from the base frame to the tray. With the mast down the tray sits at 1.33 m, so the reach comes out of the telescoping sections. Tell us the fixing height you actually work at and we confirm the reach before you order.
How much can the tray carry?
200 kg on the standard build. That covers a canopy frame section, an awning, an outdoor unit or a stack of boxes — the sort of load one or two people would otherwise hold up by hand.
Can one person set it up?
The machine stands on its own 60 × 60 cm base with two braces to fold out, so there is nothing to bolt down and no second fixing point. The mast comes down to 1.33 m for transport. Two people is easier for unloading and for lifting the mast upright.
Does it need a level surface?
Yes. The base frame has to stand on firm, level ground with all four corners loaded and the braces folded out — a slab, a roof deck or compacted hardstanding. On soft ground or a slope, put a plate under the frame or pick a different machine.
What power supply does it need?
The motor is wound for the voltage and frequency at your destination and the figure is written on the quotation drawing. Send us the site voltage and we confirm it before production.
Can a person ride on the tray?
No. The tray is a load plate with no guardrail, no gate and no passenger control. It is for holding material at height while you fix it; use a proper access platform for the person.
What does it cost, and how is freight worked out?
The unit price depends on the build and the quantity; freight is a separate line priced by weight, volume and destination port, so the quote shows the machine cost and the shipping cost side by side. Send the reach, the top type, the quantity and the port you ship to.

For work at height during installation, see OSHA 29 CFR 1926.501 on fall protection and 1926.451 on scaffolds.

Price on request200 kg · 4.5 m · tray top

Quote

Reviews

There are no reviews yet.

Be the first to review “Portable Canopy Lift, 200 kg, 4.5 m”

Your email address will not be published. Required fields are marked *

Related Products

Scroll to Top

Get A Quote

Tell us your working height, load and site conditions — we’ll come back with the right lift and a firm price within 2 hours.