Cold Storage Panel Lift, 4.5 mSKU: TMB-CP460-405701108
A 2.53 m mast on straddle legs that reach 1.5 m under the load: it lifts 460 kg to 4.5 m so a cold-storage panel can go up a wall without four people holding it.
- ✓
Held in stock in the standard 2.53 m mast build and dispatched from our own warehouse. A different leg span, mast height, colour or logo is built to order — see custom options.
- ✓
Built to the specification published here — same steel mast, copper-motor winch, wire rope and rope limiter on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
The legs go under the load, the mast goes up beside it
Panels are the one load a scissor lift cannot take: too tall, too thin and they have to go up a wall. This machine straddles the panel with three legs and lifts it on a wire rope.
Straddle legs reach under the panel
Three box-section legs, 1.5 m long with a 0.9 m span, run under the load like a pallet truck. The whole machine is 2.1 m long, so it fits along a wall line while a panel goes up.
4.5 m of lift from a 2.53 m mast
A telescopic mast with a wire rope hoist takes the load to 4.5 m — a cold-room wall height — from a mast that stands 2.53 m when closed.
460 kg on copper-motor power
A pure-copper motor drives the winch with a wire rope and pulley block. The load limit is set at 460 kg, with a rope limiter that stops the lift before the block runs out of travel.
190 kg machine, four casters
The machine itself weighs 190 kg and rolls on four yellow polyurethane casters, so two people can move it from one wall bay to the next without a pallet truck.
15 cm clearance under the legs
The leg section stands 15 cm off the floor: enough to slide under a panel edge, a pallet or a raised threshold without lifting the load first.
Blue frame, visible on site
Steel mast and legs in blue with the hoist in red — easy to pick out against insulation panels, plastic sheeting and site hoarding.
Panel lift: full technical data
Figures are for the standard build. If the machine has to pass a doorway or a site gate, check the 2.1 m overall length and the 0.9 m leg span first.
Lifting & power
| Lifting mechanism | Telescopic mast, wire rope hoist with pulley block |
| Lift height | 4.5 m |
| Load capacity | 460 kg |
| Motor | Pure copper motor on the winch |
| Safety | Rope limiter stops the lift at the end of travel |
Build
| Mast height (closed) | 2.53 m |
| Leg length | 1.5 m |
| Leg span | 0.9 m |
| Overall length | 2.1 m |
| Clearance under legs | 15 cm |
| Wheels | 4 yellow PU casters |
| Machine weight | 190 kg |

Figures above are factory-measured for this model. Manually measured dimensions may vary slightly; refer to the actual machine.
Mast, rope, legs — and where the load sits
The load rides on the leg forks, the mast carries it up, and the wire rope does the lifting. Each part is visible in the detail photos above.
Wire rope on a pulley block
A wire rope runs from the winch over a pulley block inside the mast. The rope is the wearing part, and it is visible along its whole length for inspection.
Box-section legs, 15 cm clearance
Three box-section legs carry the load at floor level with 15 cm of clearance, so a panel edge slides under without being lifted by hand first.

2.1 m long, 0.9 m wide
The machine fits along a wall line: 2.1 m overall length, 0.9 m leg span, and the mast 2.53 m when closed — under most door heads.
460 kg to 4.5 m
Rated 460 kg, which covers a cold-storage panel, a sheet of sandwich board or a glazed unit with its frame.

A mast that stays out of the load's way
A steel mast on the rear of the leg frame, telescoping to 4.5 m. Because it stands beside the load rather than under it, a full-height panel can go up without being cut.
A copper-motor winch with a wire rope and pulley block, plus a limiter that stops the lift at the end of travel. The machine weighs 190 kg.
For the loads a fork lift cannot take
Panels, boards and glazed units are long, thin and awkward. This machine takes them from the side instead of underneath, which is what makes it useful on a cold-store or a shop-fit job.
- Cold storage and freezer roomsStand panels up against the wall line and lift them into the channel at 4.5 m without four people holding the top edge.
- Shop fitting and partitioningGlazed units, partition boards and ceiling panels taken up to height with the legs straddling the frame.
- Building sitesBoards, sheets and sheets of insulation moved along a wall and lifted to first-floor height.
- WarehousesHeavy flat stock stored high: the legs go in under the stack and the mast lifts it clear.

Custom options on this panel lift
The 1.5 m leg and 2.53 m mast build is standard. Where a job needs a longer reach or a different leg span, the same mast and winch are built to your drawing.

- Leg length and span1.5 m legs on a 0.9 m span are standard; longer legs or a wider span can be built for a specific panel width.
- Mast height2.53 m closed, lifting to 4.5 m. A taller lift can be built if the wall height needs it.
- Frame colour and finishBlue frame with a red winch is standard; any specified colour can be applied.
- Your logoSend the artwork and your logo is applied before the machine leaves the factory.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this machine is 190 kg and ships on a pallet.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How high does it lift?
How much does it carry?
How does it lift a panel that has no pallet under it?
What powers the lift?
Can two people move the machine?
How much space does it need?
Can the leg length or mast height be changed?
What does it cost, and how is freight worked out?
For overhead lifting safety requirements, see OSHA 1910.179, overhead and gantry cranes.








Reviews
There are no reviews yet.