Four-Wheel Manual Push Lift PlatformSKU: TMB-FW1200-404986502
A 1200 × 700 mm deck that rises on a hydraulic scissor and rolls wherever you push it — loaded at floor level, then lifted to the bench, the dock or the rack you are working at.
- ✓
Held in stock in the standard 1200 × 700 mm build and dispatched from our own warehouse. A different deck size, deck surface, colour or logo is built to order — see custom options.
- ✓
Built to the specification published here — same single-cylinder scissor, battery box and 4.00-8 rear tyres on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
A 1200 × 700 mm deck that lifts where you leave it
The deck is big enough for a pallet footprint or a stack of crates, and it is the deck that does the lifting — you never take the load off the trolley to raise it.
1200 × 700 mm working deck
A steel deck edged with black and yellow hazard stripe, wide enough for a standard pallet footprint and long enough to take two crates end to end. The load stays on the deck from the truck to the shelf.
One cylinder, one scissor
A single hydraulic cylinder sits between the two scissor legs and drives the deck straight up. Fewer joints than a multi-stage mast, and the deck rises vertically instead of swinging out.
Battery pump, no manual pumping
The battery lives in the steel box under the frame and drives the pump. Turn the key, press the lift control and the deck climbs — no handle to pump between loads.
4.00-8 tyres at the rear, casters in front
Two pneumatic 4.00-8 tyres carry the drive end and roll over gravel, dock plates and door thresholds; two swivel casters with spring suspension steer the front and lock with a brake pedal.
Key switch and emergency stop
Power is switched with a key, so the machine cannot be started by anyone walking past it, and the red emergency stop on the rear panel cuts the pump immediately.
Push handle and rear step plate
A full-width handlebar with both grips lets one operator push and steer a loaded machine; the step plate behind the rear axle keeps the operator clear of the wheels.
Four-wheel mobile lift platform: technical data
Figures are for the standard build. Ask us for a drawing with the deck and the raised height marked if you need to check the machine against a bench, a dock or a rack.
Lifting & power
| Lifting mechanism | Single hydraulic cylinder on a scissor |
| Power source | Battery in the steel box under the deck |
| Controls | Key switch, lift control, emergency stop |
| Battery gauge | Meter on the rear panel |
| Deck height | Rises on the scissor; raised height confirmed on the drawing |
Build
| Deck size | 1200 × 700 mm |
| Deck edge | Black and yellow hazard stripe |
| Frame | Welded steel, powder coated |
| Front wheels | 2 swivel casters, spring suspension, brake |
| Rear wheels | 2 pneumatic tyres, 4.00-8 |
| Rear step | Step plate behind the rear axle |
| Handle | Full-width push handlebar |

Manually measured dimensions may vary slightly; refer to the actual machine. Load rating and raised height for a specific build are confirmed on the quotation drawing.
What carries the deck, and what carries the machine
Four things do the work: the scissor, the cylinder inside it, the battery box under the frame, and the wheels that take the weight on the floor.
One red cylinder drives the scissor
The ram sits between the scissor legs and pushes the centre joint up. Single cylinder, so there is one seal to watch instead of a set of them, and the deck rises straight.
4.00-8 tyres on the drive end
Pneumatic 4.00-8 tyres with a bolt-on rim. They roll over gravel, dock plates and yard surfaces that would stop a hard caster.

Key, gauge and stop in one panel
The key switch, the battery gauge and the red emergency stop sit together on the rear panel, within reach of the handlebar. The gauge tells you where the battery stands before the load goes on.
Step plate behind the axle
A yellow step plate sits behind the rear axle on a steel bracket. The operator stands clear of the wheels while pushing, and steps up onto it on long level runs.

1200 × 700 mm deck, battery box underneath
1200 × 700 mm of steel deck, edged in black and yellow hazard stripe so the deck edge reads against a warehouse floor. Wide enough for a pallet footprint.
Welded steel, powder coated yellow. The battery box is part of the frame, between the two axles, so nothing hangs below the machine to catch on a threshold.
The jobs where the load stays on the deck while it goes up
This is a hand-pushed platform: you wheel it to the load, lift the deck, and work at the height the deck gives you. It is not a stacker and not a forklift — it is the shortest way to stop lifting by hand.
- Warehouse and dispatchLoad the deck at floor level, roll it to the packing bench, raise it and slide the carton across instead of lifting it up.
- Workshop and assemblyUse the deck as a mobile bench that comes to the job: roll the part over, lift it to working height, and drop it back down when you are done.
- Loading bays and docksPush the loaded machine to the dock, raise the deck towards the vehicle floor, and move the goods across by hand at a height your back can take.
- Retail, events and fit-outRestock shelves, move display plinths and shift furniture without carrying each piece — the deck takes the weight, the wheels take the distance.

Custom options on this lift platform
The 1200 × 700 mm deck is the standard build. When the deck has to match your own pallet, rack or bench, the same scissor and power unit are built to your drawing.

- Deck sizeStandard 1200 × 700 mm; built to the length and width your pallet, crate or bench needs.
- Deck surfaceA plain steel deck is standard. A checker plate, a coated deck or a stainless deck can be specified for wet or food-contact work.
- Frame colour and finishYellow frame with a hazard-striped deck edge is standard. A specified colour can be applied to match the equipment already on your site.
- Your logoSend the artwork and your logo is applied before the machine leaves the factory. The marking is confirmed with you before production starts.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this machine ships on a pallet.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How big is the deck?
How does it lift?
Is it pushed by hand or driven?
What wheels does it run on?
What controls are on the machine?
Can the deck size, surface, colour or logo be changed?
What is the load rating for this build?
What does it cost, and how is freight worked out?
For powered industrial truck safety requirements, see OSHA's powered industrial trucks guidance.








Reviews
There are no reviews yet.