Professional Lifting Equipment Manufacturer

Double Arm Electric Material Lift 400 kg, 2.2–4 m

TMB-DA400-405699843

Mobile two-post material lift with a horizontal arm on each side of the mast, used to raise pipe, duct sections, coils and sheet goods to height. The mast stands 2.2 m closed and the carriage travels to 4 m raised, driven by a copper-motor electric hoist on steel wire rope; the power cable runs on a reel fixed to the mast.

Home/Scissor Lift/MEWP/Double Arm Electric Material Lift 400 kg, 2.2 – 4 m
In stock · ready to ship

Double Arm Electric Material Lift 400 kg, 2.2 – 4 mSKU: TMB-DA400-405699843

Two horizontal arms on a 2.2 m two-post mast, raised to 4 m by a copper-motor electric hoist — so a length of pipe, a duct section or a coil goes up on the machine instead of on someone's shoulder.

Load capacity
400 kg
Lift height
2.2 m closed · 4 m raised
Footprint
1.3 m × 880 mm
Machine weight
about 120 kg
Price on request
Standard build · 400 kg, 2.2 m mast and up to 4 m lift — unit price quoted with freight
Freight is quoted separately. Send us your destination port and the quantity — you get the machine price and the shipping cost in one reply, so you can compare landed cost. See Shipping & Delivery for how it works.
Request a quote
  • ✓
    Held in stock in the standard 400 kg build and dispatched from our own warehouse. A different load rating, lift height, arm length, colour or logo is built to order — see custom options.
  • ✓
    Built to the specification published here — same two-post mast, four casters and copper-motor hoist on every unit we ship.
  • ✓
    Nothing ships until you approve the freight quote in writing.
  • ✓
    Packing list, commercial invoice and bill of lading sent with every shipment.
Why this model

A pair of arms takes the load up the mast, not up a ladder

The machine is a two-post mast on a wide wheeled base, with one horizontal arm on each side. The arms sit under the pipe, the duct section or the coil, the hoist lifts, and the load arrives at height square and level — the operator stays on the floor.

01

400 kg spread over two arms

Each arm is a steel member running out from the carriage, so a length of pipe or a duct section rests on both instead of on one point. Long goods stay level as they rise, and the load sits close to the mast where the frame is strongest.

02

2.2 m mast, 4 m raised

The mast stands 2.2 m when the carriage is down, which is low enough to pass through a standard door frame. Raised, the carriage takes the arms to 4 m — a duct run at ceiling level, a mezzanine edge or the underside of a pipe rack.

03

Copper-motor hoist on wire rope

A copper-motor electric hoist lifts on steel wire rope over the top pulley, so the pull runs straight up the mast instead of sideways through the frame. The power cable rides on a reel fixed to the mast, which keeps it off the floor.

04

1.3 m × 880 mm base on four casters

The outriggers open to 1.3 m by 880 mm, wide enough that the machine does not tip when the load is at full height and off centre. Four polyurethane swivel casters, two with brakes, carry it through a door and lock it at the work point.

Specifications

Double arm electric material lift: technical data

Figures are for the standard build. Ask us for a drawing with the mast height, the footprint and the raised height marked if you need to check the machine against a door frame, a mezzanine or a ceiling run.

Lifting & power

Lifting mechanism Two-post mast with a sliding carriage and one horizontal arm each side
Drive Electric hoist — copper motor, steel wire rope over a top pulley
Lift height 2.2 m closed, up to 4 m raised
Arms One steel arm each side of the mast, carried on the sliding carriage
Power cable Cable reel mounted on the mast
Power supply Confirmed per destination on the quotation drawing

Build

Footprint 1.3 m × 880 mm with the outriggers open
Lowest arm height 180 mm
Top beam 630 mm across the beam that ties the two posts at the top
Overall height 2.2 m with the carriage down
Load capacity 400 kg
Machine weight About 120 kg
Frame Steel, red; arms and outriggers black
Wheels Four polyurethane swivel casters, two with brakes
Dimension drawing of the double arm material lift marked 2.2 m mast height, 1.3 m and 880 mm footprint, 180 mm at the lowest arm position and 630 mm across the top beam
Dimensions: 2.2 m mast height, 1.3 m × 880 mm footprint and 180 mm with the arms at their lowest setting. The 630 mm dimension in the drawing is the top beam — the member that ties the two posts together above the carriage.
Built to order on this model Load rating, lift height, arm length and the frame colour can all be changed. Send the drawing or the dimensions you work to and we confirm the build, the materials and the finish before production starts.

Manually measured dimensions may vary slightly; refer to the actual machine. Load rating, lift height and arm length for a specific build are confirmed on the quotation drawing.

Build detail

What carries the load, and what lifts it

The mast and its sliding carriage carry the arms; the hoist on the lower frame does the lifting; the outriggers and casters keep the machine on the floor while the load is at the top.

Red two-post mast with the black sliding carriage and the steel wire ropes running to the top pulley
Mast

Two posts, 2.2 m, tied by a 630 mm top beam

Structure

Two steel posts run the full height and are joined at the top by a 630 mm beam, with a brace part way down. The load hangs between them, so the pull stays inside the frame instead of bending one post away from the other.

Carriage

The carriage the arms hang from

Travel

The arms are bolted to a carriage that runs up and down the mast on rollers. Four wire ropes take the load, so the carriage stays level as it climbs and the arms do not cock to one side under an offset load.

Electric hoist with a copper motor and the yellow cable reel on the mast, above the black outriggers and casters
Hoist

Copper motor at the foot of the mast

Drive

The hoist is mounted low on the frame, where its weight helps hold the machine down, and pulls on steel wire rope over the top pulley. The yellow reel beside it carries the power cable and keeps it out of the way of the wheels.

Rope

Rope runs straight up the mast

Lifting

The rope leaves the hoist, runs up the inside of the mast and over the top pulley to the carriage. Because the pull is vertical, the mast takes it in compression rather than in bending — which is why a 120 kg machine can raise 400 kg.

Black steel outriggers and four polyurethane casters under the red mast base of the material lift
Base

Outriggers open to 1.3 m × 880 mm

Stability

The outriggers swing out from the mast foot and pin in place. The wider the spread, the less the machine leans when the load is at 4 m and sits to one side of the mast — measure the spread you get before you plan the route through a doorway.

Wheels

Four casters, two with brakes

Moving

Polyurethane swivel casters roll on a concrete floor and over a workshop threshold. Two of them brake, so the machine can be locked at the work point while the hoist is running and the arms are loaded.

Where it is used

The jobs where the load goes up and the operator stays down

One operator, one machine and the load at height in a single lift: ductwork, pipe runs, coil and sheet goods, and anything else that is too long or too heavy to hand up a ladder.

  • Duct and ventilation installationA duct section goes up between the arms and is raised to the ceiling grid, where it can be pushed across onto hangers while the installer works from a step or a platform.
  • Pipe runs and pipe racksLengths of pipe rest on both arms and rise level, so the run stays straight as it goes up to the rack — no one holding one end at head height.
  • Coils, sheet and panel goodsA coil or a stack of sheet sits across the arms and is lifted to the feed height of a press or a shear instead of being walked up a ramp.
  • Warehouse, workshop and siteThe footprint is small enough to move between racks and through a door, so the same machine serves a store, a fabrication bay and a fit-out.
  • Ductwork
  • Pipe
  • Coil
  • Sheet
  • Warehouse
  • Fit-out
Built to order

Custom options on this double arm lift

The 400 kg build with a 2.2 m mast and 4 m of lift is the standard machine. When the load is heavier, longer or has to reach higher, the same mast and hoist are built to your drawing.

Dimension drawing of the double arm material lift with mast height, footprint and lowest arm position marked
Standard build shown: 2.2 m mast, 1.3 m × 880 mm footprint, 180 mm at the lowest arm setting, 400 kg capacity. Load rating, lift height, arm length, colour and branding are built to order.
  • Load rating400 kg is standard. A heavier rating is built with a thicker mast section and a larger hoist.
  • Lift height2.2 m closed and 4 m raised is standard. A taller mast can be built where the ceiling allows it.
  • Arm length and typeThe standard arms take pipe, duct and coils. Longer arms, a flat plate or a cradle for round goods can be fitted for a specific load.
  • Frame colour and your logoRed frame with black arms is standard. A specified colour and your logo can be applied before the machine leaves the factory.
How a built-to-order unit is confirmed Send the load, how long and how wide it is, the height it has to reach and the doorway it has to pass through. We confirm the mast height, the footprint, the arm type and the finish on a drawing before production starts.
Shipping & delivery

Freight is quoted separately and confirmed before dispatch

We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this machine ships as one crate on a pallet.

  1. You place the order online

    Your order is recorded and the machine is reserved for you while the freight is quoted.

  2. We send a freight quote in 24–48 hours

    Priced to your nearest port, with transit time, or to your door as DDP if you prefer.

  3. You confirm and pay the freight

    One invoice for the shipping cost. Nothing is dispatched until you approve it.

  4. We book, load and send documents

    Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.

Why we do not charge freight at checkout LCL and FCL rates change weekly and depend on the port, the total volume and whether you combine this lift with other machines. A fixed online rate would either overcharge you or force us to invoice the difference afterwards — so we quote it properly instead.
What the freight quote includes Cost to your port or door, the shipping line and transit time, the earliest departure we can make, and the documents that travel with the goods. If we can cut your cost by combining this machine with others in one container, we will tell you before you pay.
Questions buyers ask

Frequently asked questions

How high does it lift?
The mast stands 2.2 m with the carriage down and the arms travel to 4 m raised, lifted by the hoist on steel wire rope. Check the headroom above the work point for 4 m of lift plus the height of the load, and check that the 2.2 m closed height passes the door frame on the route in.
How much can it carry?
400 kg on the standard build, with a machine weight of about 120 kg. The load is shared by the two arms and carried on four wire ropes, so long goods stay level as they rise. A heavier rating is built to order and written on the quotation drawing.
What can it lift?
Pipe and pipe spools, duct sections, coils, sheet and panel goods — anything that can rest across the two arms and be carried up the mast. The arms take the load from below, so it has to be something that sits on them rather than hanging from a hook.
How is it powered?
By an electric hoist with a copper motor, mounted low on the frame and pulling on steel wire rope over the top pulley. The power cable rides on a reel fixed to the mast. Supply voltage is confirmed per destination on the quotation drawing.
Does it move on its own?
No — it is pushed, not driven. Four polyurethane swivel casters carry it on a concrete floor, and two of them have brakes so the machine can be locked at the work point. It is a one-person machine on a level floor; it is not a rough-ground unit.
How much floor does it take?
1.3 m by 880 mm with the outriggers open, which is the working footprint — the outriggers have to be open and pinned before the load goes up. Check the narrowest doorway and the tightest corner on the route against that 880 mm, and against the 1.3 m spread once you are through.
How low does it go?
The arms go down to 180 mm from the floor, so a load can be picked up from a pallet, a stillage or the floor itself without a ramp.
What does it cost, and how is freight worked out?
The unit price depends on the build and the quantity; freight is a separate line priced by weight, volume and destination port, so the quote shows the machine cost and the shipping cost side by side. Send the load, the height you need, the quantity and the port you ship to.

For materials handling equipment used in general industry, see OSHA 29 CFR 1910.176 on materials handling and storage.

Price on request400 kg · 2.2–4 m

Quote

Reviews

There are no reviews yet.

Be the first to review “Double Arm Electric Material Lift 400 kg, 2.2–4 m”

Your email address will not be published. Required fields are marked *

Related Products

Scroll to Top

Get A Quote

Tell us your working height, load and site conditions — we’ll come back with the right lift and a firm price within 2 hours.