Portable Canopy Lift, 200 kg, 4.5 mSKU: TMB-PC200-405740245
A flat black tray on a single mast: set the canopy frame on it, wind it up to the fixing line, and both your hands are free for the drill instead of holding the frame.
- ✓
Held in stock in the standard 200 kg, 4.5 m build with the flat tray and dispatched from our own warehouse. A different top, reach or colour is built to order — see custom options.
- ✓
Built to the specification published here — same mast, winch and base frame on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
A third hand at the fixing line
Canopy and awning work is mostly one person holding the section up and another drilling. This machine takes the holding: the frame sits on the tray, the tray goes to height, and the fixing is done with two free hands.
A flat tray, not a hook
The top is a flat black steel tray with a rim, so a canopy frame, an awning section, an air-conditioning unit or a box sits on it and stays put. Nothing has to be slung or strapped, and the load comes off the same way it went on.
4.5 m of reach, 1.33 m in the van
The mast telescopes down to 1.33 m, which is the length of a step ladder, and still puts the tray at 4.5 m. It goes in the back of a van with the rest of the kit and stands up on site in the time it takes to fold the braces out.
Winch and motor on the base frame
The electric winch, the copper-wound motor and the rope drum all sit at floor level, and four falls of steel wire rope run up the mast to the tray. The heavy part never leaves the ground, and the part you would service is the part you can reach.
Pendant control, operator at the base
The hand control hangs on a cable, so the person working the lift stands at the foot of the mast with a clear view of the load and the fixing line. Let go of the button and the tray holds where it is.
Portable canopy lift: technical data
Figures are for the standard build. The drawing below is measured with the mast down — 1.33 m to the underside of the tray, on a 60 × 60 cm base frame. Reach is measured from the base frame.
Lifting & reach
| Lifting mechanism | Electric winch on the base frame, four falls of steel wire rope to the tray |
| Max reach | 4.5 m from the base frame |
| Stowed height | 1.33 m to the underside of the tray |
| Mast | Single square steel mast, telescoping sections |
| Rope | 4 × steel wire rope, load shared at four points |
Top, base & power
| Top | Flat black steel tray with a rim, bolted to the mast head |
| Load capacity | 200 kg |
| Base frame | 60 × 60 cm, two folding braces to the corners |
| Drive | Copper-wound electric motor and rope drum on the base frame |
| Control | Hand pendant on a cable — up and down |
| Finish | Orange-red mast and base frame, red winch cover, black tray |
| Power supply | Confirmed per destination on the quotation drawing |
| Installation | Free-standing on its own base — nothing to fix to the building |

Manually measured dimensions may vary slightly; refer to the actual machine. Reach, top type and power supply for a specific build are confirmed on the quotation drawing.
Tray at the top, winch at the bottom
Everything that carries load is either on the base frame or bolted to the mast head: the tray is a flat top you can set things on, and the winch that lifts it never leaves the ground.

Flat, with a rim to stop a slide
The tray is a flat steel top with a raised rim all round, bolted to the mast head. A frame, a unit or a box put on it stays where it is put, and the rim catches the load if it shifts as the mast starts to move.
Set it, wind it up, fix it
Load the tray at the bottom where you can reach it, raise it to the fixing line, bolt the section, lower the tray and load the next one. The machine stays where it is for the whole run instead of being moved for every piece.

Four corners, two braces
The base is a 60 × 60 cm square frame that stands on the ground with two braces from the mast out to the corners. Fold the braces out on firm level ground and the machine is ready — nothing to bolt down, which is what keeps it portable.
Winch and drum at ground level
Motor, drum and rope sit on the frame at the foot of the mast, inside a red guard. Four falls of rope go up to the tray, so the load is shared at four points and the tray stays level even when the frame is set down off centre.
Canopies, carports and awnings — the frame that is too big to hold
A canopy section is light enough for one man to carry and awkward enough that two are needed to fit it. Put it on the tray and one man can do the fixing, at the height it is going to stay.
- Canopy and carport framesAn arched or flat canopy frame is assembled on the ground, set on the tray, raised to the wall plate and bolted while it is held level — no scaffold deck, no two men on ladders.
- Awnings and entrance canopiesAn awning section or a polycarbonate sheet is offered up to the fixing line at the right height and angle, and stays there while the brackets are drilled and set.
- Signage and light boxesA sign panel is set on the tray and raised to the fascia, where it is fixed without being held up by hand against the wall.
- Rooftop plant and unitsOutdoor units, vents and duct sections go up the outside of a building on the tray, on a machine that stands on the roof or the slab rather than needing a crane.
Custom options on this canopy lift
The 200 kg machine with 4.5 m of reach and the flat tray is the standard build. The top, the reach and the finish are the parts customers change.

- TopThe flat tray is standard. A U-shaped cradle with padded arms is the other option on the same mast — better for pipe, duct and panels, which need to stand upright rather than lie flat.
- Reach4.5 m is standard. A different mast length is built for a specific job — tell us the fixing height you work at and where the machine will stand.
- FinishOrange-red mast and base frame with a red winch cover as standard. Other colours are confirmed when you order, and your logo can be applied before the machine leaves the factory.
- Power supplyThe motor is wound for the voltage and frequency at your destination — send the site voltage and it is stated on the quotation drawing.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this one packs down to a single long crate, which keeps the shipping cost low.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
What is the difference between this and the U cradle version?
How high does it reach?
How much can the tray carry?
Can one person set it up?
Does it need a level surface?
What power supply does it need?
Can a person ride on the tray?
What does it cost, and how is freight worked out?
For work at height during installation, see OSHA 29 CFR 1926.501 on fall protection and 1926.451 on scaffolds.








Reviews
There are no reviews yet.