Professional Lifting Equipment Manufacturer

Cold Storage Panel Lift 4.5 m

TMB-CP460-405701108

Mobile mast lift for cold-storage panels and sheets. Blue steel mast 2.53 m high, straddle legs 1.5 m long with a 0.9 m span and 2.1 m overall length, 15 cm ground clearance under the legs. Electric winch with a copper motor and wire rope lifting to 4.5 m, load limited to 460 kg, machine weight 190 kg, four yellow polyurethane casters.

Home/Mast Lift/Cold Storage Panel Lift, 4.5 m
In stock · ready to ship

Cold Storage Panel Lift, 4.5 mSKU: TMB-CP460-405701108

A 2.53 m mast on straddle legs that reach 1.5 m under the load: it lifts 460 kg to 4.5 m so a cold-storage panel can go up a wall without four people holding it.

Lift height
4.5 m
Load capacity
460 kg
Mast height
2.53 m closed
Leg span
1.5 m long · 0.9 m wide
Price on request
Standard build · 2.53 m mast, 1.5 m legs — unit price quoted with freight
Freight is quoted separately. Send us your destination port and the quantity — you get the machine price and the shipping cost in one reply, so you can compare landed cost. See Shipping & Delivery for how it works.
Request a quote
  • ✓
    Held in stock in the standard 2.53 m mast build and dispatched from our own warehouse. A different leg span, mast height, colour or logo is built to order — see custom options.
  • ✓
    Built to the specification published here — same steel mast, copper-motor winch, wire rope and rope limiter on every unit we ship.
  • ✓
    Nothing ships until you approve the freight quote in writing.
  • ✓
    Packing list, commercial invoice and bill of lading sent with every shipment.
Why this model

The legs go under the load, the mast goes up beside it

Panels are the one load a scissor lift cannot take: too tall, too thin and they have to go up a wall. This machine straddles the panel with three legs and lifts it on a wire rope.

01

Straddle legs reach under the panel

Three box-section legs, 1.5 m long with a 0.9 m span, run under the load like a pallet truck. The whole machine is 2.1 m long, so it fits along a wall line while a panel goes up.

02

4.5 m of lift from a 2.53 m mast

A telescopic mast with a wire rope hoist takes the load to 4.5 m — a cold-room wall height — from a mast that stands 2.53 m when closed.

03

460 kg on copper-motor power

A pure-copper motor drives the winch with a wire rope and pulley block. The load limit is set at 460 kg, with a rope limiter that stops the lift before the block runs out of travel.

04

190 kg machine, four casters

The machine itself weighs 190 kg and rolls on four yellow polyurethane casters, so two people can move it from one wall bay to the next without a pallet truck.

05

15 cm clearance under the legs

The leg section stands 15 cm off the floor: enough to slide under a panel edge, a pallet or a raised threshold without lifting the load first.

06

Blue frame, visible on site

Steel mast and legs in blue with the hoist in red — easy to pick out against insulation panels, plastic sheeting and site hoarding.

Specifications

Panel lift: full technical data

Figures are for the standard build. If the machine has to pass a doorway or a site gate, check the 2.1 m overall length and the 0.9 m leg span first.

Lifting & power

Lifting mechanism Telescopic mast, wire rope hoist with pulley block
Lift height 4.5 m
Load capacity 460 kg
Motor Pure copper motor on the winch
Safety Rope limiter stops the lift at the end of travel

Build

Mast height (closed) 2.53 m
Leg length 1.5 m
Leg span 0.9 m
Overall length 2.1 m
Clearance under legs 15 cm
Wheels 4 yellow PU casters
Machine weight 190 kg
Dimension drawing: 1.5 m leg length, 0.9 m span, 2.1 m overall length, 2.53 m mast height, 15 cm leg clearance
Standard build: legs 1.5 m long with a 0.9 m span and 2.1 m overall length, mast 2.53 m closed and lifting to 4.5 m.
Built to order on this model Leg length, leg span, mast height, frame colour and your logo can all be changed. Send the drawing or artwork and we confirm dimensions, materials and finish before production starts.

Figures above are factory-measured for this model. Manually measured dimensions may vary slightly; refer to the actual machine.

Build detail

Mast, rope, legs — and where the load sits

The load rides on the leg forks, the mast carries it up, and the wire rope does the lifting. Each part is visible in the detail photos above.

Yellow caster, box-section leg channel and wire rope pulley block

Rope

Wire rope on a pulley block

Hoist

A wire rope runs from the winch over a pulley block inside the mast. The rope is the wearing part, and it is visible along its whole length for inspection.

Legs

Box-section legs, 15 cm clearance

Legs

Three box-section legs carry the load at floor level with 15 cm of clearance, so a panel edge slides under without being lifted by hand first.

Dimension drawing of the panel lift footprint and mast height
Footprint

2.1 m long, 0.9 m wide

Footprint

The machine fits along a wall line: 2.1 m overall length, 0.9 m leg span, and the mast 2.53 m when closed — under most door heads.

Capacity

460 kg to 4.5 m

Load

Rated 460 kg, which covers a cold-storage panel, a sheet of sandwich board or a glazed unit with its frame.

Cold storage panel lift, whole machine
Mast

A mast that stays out of the load's way

Mast

A steel mast on the rear of the leg frame, telescoping to 4.5 m. Because it stands beside the load rather than under it, a full-height panel can go up without being cut.

Winch

A copper-motor winch with a wire rope and pulley block, plus a limiter that stops the lift at the end of travel. The machine weighs 190 kg.

Where it is used

For the loads a fork lift cannot take

Panels, boards and glazed units are long, thin and awkward. This machine takes them from the side instead of underneath, which is what makes it useful on a cold-store or a shop-fit job.

  • Cold storage and freezer roomsStand panels up against the wall line and lift them into the channel at 4.5 m without four people holding the top edge.
  • Shop fitting and partitioningGlazed units, partition boards and ceiling panels taken up to height with the legs straddling the frame.
  • Building sitesBoards, sheets and sheets of insulation moved along a wall and lifted to first-floor height.
  • WarehousesHeavy flat stock stored high: the legs go in under the stack and the mast lifts it clear.
  • Cold store
  • Shop fit
  • Panels
  • Boards
  • Site
  • Warehouse
The blue panel lift standing outdoors with the mast upright
Built to order

Custom options on this panel lift

The 1.5 m leg and 2.53 m mast build is standard. Where a job needs a longer reach or a different leg span, the same mast and winch are built to your drawing.

Detail of the leg channel, caster and rope block on the panel lift
Standard build shown: blue steel mast and legs, red winch, yellow PU casters, wire rope on a pulley block. Leg length, span, mast height and colour are built to order.
  • Leg length and span1.5 m legs on a 0.9 m span are standard; longer legs or a wider span can be built for a specific panel width.
  • Mast height2.53 m closed, lifting to 4.5 m. A taller lift can be built if the wall height needs it.
  • Frame colour and finishBlue frame with a red winch is standard; any specified colour can be applied.
  • Your logoSend the artwork and your logo is applied before the machine leaves the factory.
How a built-to-order unit is confirmed Send the drawing or artwork together with the leg length, span, lift height, colour and quantity you need. We confirm dimensions, materials and finish before production starts.
Shipping & delivery

Freight is quoted separately and confirmed before dispatch

We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this machine is 190 kg and ships on a pallet.

  1. You place the order online

    Your order is recorded and the machine is reserved for you while the freight is quoted.

  2. We send a freight quote in 24–48 hours

    Priced to your nearest port, with transit time, or to your door as DDP if you prefer.

  3. You confirm and pay the freight

    One invoice for the shipping cost. Nothing is dispatched until you approve it.

  4. We book, load and send documents

    Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.

Why we do not charge freight at checkout LCL and FCL rates change weekly and depend on the port, the total volume and whether you combine this lift with other machines. A fixed online rate would either overcharge you or force us to invoice the difference afterwards — so we quote it properly instead.
What the freight quote includes Cost to your port or door, the shipping line and transit time, the earliest departure we can make, and the documents that travel with the goods. If we can cut your cost by combining this machine with others in one container, we will tell you before you pay.
Questions buyers ask

Frequently asked questions

How high does it lift?
4.5 m from a mast that stands 2.53 m when closed. That is cold-room wall height, a first-floor panel line or a high racking level.
How much does it carry?
460 kg. The rating covers a cold-storage panel, a sheet of sandwich board or a glazed unit with its frame.
How does it lift a panel that has no pallet under it?
The legs straddle the load: three box-section legs 1.5 m long on a 0.9 m span slide under the panel edge with 15 cm of clearance, and the mast lifts from beside the load, not beneath it.
What powers the lift?
A pure-copper motor driving a wire rope winch with a pulley block. A rope limiter stops the lift at the end of its travel.
Can two people move the machine?
Yes — it weighs 190 kg and rolls on four yellow polyurethane casters, so it can be walked from one wall bay to the next.
How much space does it need?
2.1 m of length and 0.9 m of width on the floor, with the mast 2.53 m high when closed. Check your door head and gate width against those figures.
Can the leg length or mast height be changed?
Yes — leg length, leg span, mast height, colour and logo are all made to order. Tell us the panel size and the height it has to reach, and we confirm the build on a drawing.
What does it cost, and how is freight worked out?
The unit price depends on the build and the quantity; freight is a separate line priced by weight, volume and destination port, so the quote shows the machine cost and the shipping cost side by side. Send the leg length, the lift height, the quantity and the port you ship to.

For overhead lifting safety requirements, see OSHA 1910.179, overhead and gantry cranes.

Price on request4.5 m · 460 kg · 190 kg machine

Quote

Reviews

There are no reviews yet.

Be the first to review “Cold Storage Panel Lift 4.5 m”

Your email address will not be published. Required fields are marked *

Related Products

Scroll to Top

Get A Quote

Tell us your working height, load and site conditions — we’ll come back with the right lift and a firm price within 2 hours.