Cage Cargo Lift, 4 m, 800 × 800 mm DeckSKU: TMB-CG400-514121768
A cage on two posts: sacks, cartons and drums go on an 800 × 800 mm steel deck inside an 800 mm guardrail, and come up 4 m without being handed up a stair.
- ✓
Held in stock in the standard 4 m, 800 × 800 mm build and dispatched from our own warehouse. A different deck, height or colour is built to order — see custom options.
- ✓
Built to the specification published here — same posts, cylinder and cage on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
A cage, so the load stays on the deck
For goods that have to change floor and will not sit still on a bare platform: sacks, cartons, drums, parts boxes. The deck is fenced on the sides, the two posts take the load, and the machine stands in the footprint of a doorway.
80 × 80 cm deck inside a guardrail
The load plate is 800 × 800 mm of steel with an 800 mm guardrail framed around it. Sacks lean on the rail instead of sliding off the edge, and the deck takes a pallet truck nose or a stack of cartons loaded from one side.
Cylinder up the middle, chain and rope out
A hydraulic cylinder stands between the two posts and pushes a crosshead up. Chain and steel wire rope connect the crosshead to the cage, and the rope runs over a pulley at the head — so the cage rises with the cylinder but is carried by the rope.
Fall arrester and two limit switches
A fall arrester sits at the head of the frame and two limit switches with roller levers are mounted on the post. The switches stop the cage at the top and bottom of the run, and the arrester is the backstop if a rope or chain lets go.
Push-button control on the wall
The control box is a wall-mounted station with push buttons and a key switch, fitted beside the opening rather than on the moving cage. The operator stands at the landing with a clear view of the deck as it comes up.
Cage cargo lift: technical data
Figures are for the standard build. The drawing below shows 4000 mm overall, an 800 × 800 mm deck and an 800 mm guardrail — send your floor-to-floor height and we confirm the post length against your building.
Lifting & safety
| Lifting mechanism | Hydraulic cylinder between the posts, chain and steel wire rope to the cage |
| Rope routing | Steel wire rope over a pulley at the head of the frame |
| Total height | 4000 mm |
| Fall arrester | Fitted at the head of the frame |
| Limit switches | Two, with roller levers on the post — top and bottom of the run |
| Control | Wall-mounted push-button box with key switch |
Deck & installation
| Deck | 800 × 800 mm steel load plate |
| Guardrail | 800 mm high, framed around the deck |
| Posts | Two black steel posts, joined by a top beam and a foot beam |
| Finish | Black posts, red cage and deck frame |
| Fixing | Fixed unit at the opening — brackets on the posts, confirmed on the drawing |
| Load capacity | Stated on the quotation drawing for your build |
| Power supply | Confirmed per destination on the quotation drawing |

Manually measured dimensions may vary slightly; refer to the actual machine. Deck size, height, load rating and power supply for a specific build are confirmed on the quotation drawing.
Two posts, one cylinder, a fenced deck
The cylinder does the pushing, chain and rope carry the cage, the guardrail keeps the load on the deck, and the fall arrester sits at the head as the backstop.

The cylinder pushes, the rope carries
The hydraulic cylinder stands between the two posts and drives a crosshead up. Chain and steel wire rope link that crosshead to the cage and the rope runs over the pulley at the head, so the cage rises with the cylinder but hangs on the rope — the cylinder supplies the force, the rope takes the weight.
Arrester at the head, switches on the post
The fall arrester is mounted at the top of the frame, where it can catch the carriage if a rope or chain fails. Two limit switches with roller levers sit on the post and cut the drive at the top and bottom of the travel, so the cage stops before it reaches the end of the frame.
A deck with a fence round it
The load plate is steel, 800 × 800 mm, framed by a guardrail 800 mm high. Sacks and cartons lean on the rail as the cage starts and stops, and the open side is where goods go on — the deck comes down level with the floor so they are slid on rather than lifted over a lip.
The buttons stay on the wall
The control station is a wall box with push buttons and a key switch, fitted beside the opening. Nothing electrical travels with the cage, the operator works from the landing, and the key switch keeps the lift out of use when the key is not in it.
Stores, workshops and mezzanines — goods that go up, not people
A cage lift is for the back of a building: it takes the footprint of a doorway, stands against a wall, and moves what should not be carried up a stair several times a shift.
- Sacks, grain and feed storesBags come off a pallet at floor level onto the deck and go up to the loft or the floor above, with the guardrail keeping the stack together on the way.
- Warehouse and mezzanine levelsCartons and small pallets move between a ground-floor store and a mezzanine, loaded from the open side at both landings.
- Workshops and parts storesHeavy components, drums and boxes go up to a parts loft without a forklift and without blocking the stair for the rest of the shift.
- Basement and cellar deliveriesDeliveries at street level go down through a hatch or stairwell opening into a basement store, on a cage small enough to fit beside the stairs.
Custom options on this cage lift
The 4000 mm frame with an 800 × 800 mm cage is the standard machine. Deck size, height and the way it is fixed are the parts customers change.

- Deck size800 × 800 mm is standard. A wider or deeper deck is built on the same posts — tell us the footprint of what you load and which side it comes on.
- Overall height4000 mm is standard. A taller frame is built for a higher floor, and a lower one for a tight opening — send the floor-to-floor height and the headroom above the upper landing.
- FixingThe posts are set at the opening and fixed before use. Send photos of the wall, the floor and the opening and we confirm the brackets on the drawing.
- FinishBlack posts with a red cage as standard. Other colours are confirmed when you order, and your logo can be applied before the machine leaves the factory.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this one ships as a frame and a cage in one crate.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How high does it lift?
What is the load capacity?
What keeps the load on the deck?
What happens if a rope or chain fails?
Where is the control?
Does it need a pit or a shaft?
Can people ride on it?
What does it cost, and how is freight worked out?
For fixed lifting installations used in general industry, see OSHA 29 CFR 1910.176 on materials handling and storage.











Reviews
There are no reviews yet.