Electric Hydraulic Lifting Platform 1.5 mSKU: TMB-LP500-403375394
A battery lift platform that puts a 905 × 500 mm deck at 1500 mm — level with a box-truck bed, a mezzanine rail or a packing bench — then comes back down to 360 mm so you can load it standing on the floor.
- ✓
Held in stock in the standard 905 × 500 mm build and dispatched from our own warehouse. A different platform size, deck material, colour or logo is built to order — see custom options.
- ✓
Built to the specification published here — same two-stage scissor, sealed cylinder and 140 kg frame on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
Reaches 1500 mm without a ramp, a hoist or a second pair of hands
A 500 kg load on a deck that ends up 1500 mm off the floor is the whole point of this machine: you load at floor level, press a button, and push the goods off at truck-bed or bench height.
1500 mm lift from a 360 mm start
Two stacked scissor stages take the 50 mm deck from 360 mm to 1500 mm. That lands level with a box-truck bed, a mezzanine rail or a packing bench, so the load slides across instead of being lifted.
500 kg on a 140 kg cart
The frame is welded steel and the machine still weighs 140 kg, so one operator can push it loaded across a yard or into a lift. Fix the brakes before you raise the deck and it stays put.
Two-stage scissor on a sealed cylinder
Both stages run on one hydraulic cylinder sitting between the leg sets. The cylinder is sealed, so there is no oil film on the deck or the floor, and both raising and lowering are powered — nothing to bleed or pump by hand.
Battery and charger inside the box
The battery is carried in the control box and charged from a normal wall socket with the charger supplied. No lead running across the loading bay and no fuel engine to service.
50 mm deck on a steel plate
The platform is 905 × 500 mm and 50 mm thick: a coated top over a steel plate, so a pallet edge or a crate corner does not dent the working surface.
Control panel within reach of the handle
Battery level display, rise and down buttons, key switch and a red emergency stop are all on the panel you are already holding. The operator sees the state of the battery before the load goes on.
Electric hydraulic lifting platform: full technical data
Figures are factory-measured on the assembled machine. Ask us for a drawing if you need to check the platform against a specific truck bed, doorway or lift car.
Lifting & power
| Lifting mechanism | Two-stage scissor, one hydraulic cylinder |
| Power source | Battery in the control box, charger supplied |
| Controls | Rise and down buttons, key switch, emergency stop |
| Battery display | Level indicator on the control panel |
| Platform height | 360 mm down · 1500 mm up |
| Rated capacity | 500 kg |
Build
| Platform size | 905 × 500 mm |
| Deck thickness | 50 mm |
| Frame | Welded steel, powder coated |
| Wheels | 4 casters, 125 mm, red PU tread, with brakes |
| Handle | Tubular push handle on the control box |
| Machine weight | 140 kg |

All figures above are for this model only and are factory-measured. Manually measured dimensions may vary slightly; refer to the actual machine.
What holds 500 kg at 1500 mm
Three parts carry the load: the scissor leg sets, the cylinder that drives them, and the casters that take the weight on the floor. Each one is visible in the photos above.
Two scissor stages, one centre pin
Each stage is an X-shaped leg set on a centre pin. Two stages stacked give the 1140 mm of travel between 360 mm and 1500 mm without lengthening the machine.
Sealed cylinder, powered both ways
The ram sits between the leg sets and pushes the centre pin up. Sealed, so nothing weeps onto the deck, and lowering is powered rather than a release valve.

Battery, display and stop in one box
Battery level display, rise and down buttons, key switch and the red emergency stop sit on the panel you push. The battery itself is inside the box, behind the panel.
Charges from a wall socket
The charger comes with the machine. Plug it in between shifts and the level display tells you where the battery stands before the next load.

905 × 500 mm deck, 140 kg machine
905 × 500 mm of working deck, 50 mm thick. Big enough for a crate or a half-pallet, short enough to turn inside a racking aisle.
Four 125 mm red PU wheels with brakes. Roll on concrete, asphalt and epoxy floor; the brake pedal locks the machine before the deck goes up.
The jobs that need floor-to-height, not floor-to-floor
This is the machine you buy when the load arrives on the floor and has to end up at vehicle or bench height. It is not a stacker and not a forklift — it is the shortest way to take a 500 kg lift out of the job.
- Warehouse and dispatchLoad the deck at floor level, raise it to the packing bench or the tailgate, and slide the carton or crate across without a ramp or a second person.
- Van and truck loadingAt 1500 mm the deck is level with a box-truck bed. Push the load straight from the platform onto the vehicle floor, then lower and roll back for the next one.
- Workshop and assemblyRaise the platform to working height as a mobile bench, then drop it back to 360 mm and push the part away on the machine.
- Mezzanine and racking transfersTakes the lift height out of the first metre and a half — the part of a transfer that is hardest on the back and the one most often done by hand.
Custom options on this lifting platform
The 905 × 500 mm platform is the standard build held in stock. When the platform has to match your own pallet, rack or vehicle floor, the same scissor and power unit are built to your drawing.

- Platform sizeStandard 905 × 500 mm; built to the length and width your pallet, crate or vehicle floor needs, within the 500 kg rating.
- Deck materialA coated top over a steel plate is standard. A plain steel deck, a checker plate or a stainless deck can be specified for wet or food-contact work.
- Frame colour and finishYellow platform on a black scissor frame is standard. A specified colour can be applied to match the equipment already on your site.
- Your logoSend the artwork and your logo is applied before the machine leaves the factory. The marking is confirmed with you before production starts.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — this machine is 140 kg and ships on a pallet.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How much does it lift, and how high?
Is the lift manual or powered?
How big is the platform?
Can one person move a 500 kg machine?
Does the platform stay level as it goes up?
What do the controls look like?
Can the platform size, colour or logo be changed?
What does it cost, and how is freight worked out?
For powered industrial truck safety requirements, see OSHA's powered industrial trucks guidance.








Reviews
There are no reviews yet.