Hydraulic Goods Lift, 700 kg, 3 mSKU: TMB-GL700-404258022
A 700 kg caged carrier lifted by a cylinder between the posts, with three chain falls over sheaves at the head. It stands on its own base and bolts down — no shaft, no pit.
- ✓
Held in stock in the standard build and dispatched from our own warehouse. A taller frame, a wider cage or another colour is built to order — see custom options.
- ✓
Built to the specification published here — same frame, cylinder, chains and cage on every unit we ship.
- ✓
Nothing ships until you approve the freight quote in writing.
- ✓
Packing list, commercial invoice and bill of lading sent with every shipment.
A cylinder does the work, chains keep it level
A fixed lift for the back of a warehouse or the side of a workshop, where goods have to change floor and there is no shaft: it stands on its own base and the carrier is a cage you load from the front.
700 kg on a plate floor
The carrier is a cage with a steel plate floor, rated to 700 kg. A pallet, a stack of cartons or a drum goes in through the open front and sits flat on the plate — nothing balances on two forks.
Cylinder between the posts
A hydraulic cylinder stands in the middle between the two posts and does the lifting. The power unit sits at the foot of the frame with its hose, so the oil and the motor are on the floor where they can be reached.
Three chain falls at the head
Three chains run from sheaves at the head of the frame down to the cage, so the carriage is carried at several points instead of one. That is what keeps a loaded cage level when the weight sits to one side.
A frame that bolts down
The frame is welded steel tube standing on a base with floor plates. It is bolted to a sound floor and needs no shaft built around it — about 200 kg of machine, and nothing to dig.
Hydraulic goods lift: technical data
One standard machine: 700 kg, 3 m of lift, a cylinder plus three chain falls. The numbers below are the machine as shipped.
Capacity & lifting
| Load capacity | Up to 700 kg |
| Lifting height | 3 m |
| Lifting | Hydraulic cylinder between the posts |
| Chain | Three chain falls over sheaves at the head |
| Machine weight | About 200 kg |
| Motor | Copper-wire motor on the power unit |
Frame & carrier
| Material | Welded steel tube and plate |
| Carrier | Cage with a steel plate floor |
| Cage front | Open, with a mid rail |
| Base | Base frame with floor plates, bolted down |
| Control | Push-button station at the loading side |
| Finish | Blue as standard |
| Power supply | Confirmed per destination on the quotation drawing |

Manually measured dimensions may vary slightly; refer to the actual machine. Lifting height, cage size, colour and power supply for a specific build are confirmed on the quotation drawing.
Cage, chain, cylinder, base
The carrier runs between two posts, a cylinder pushes it up, three chains keep it level, and the whole frame stands on a base that is bolted to the floor.

A cage you load from the front
The carrier is a welded cage: a plate floor, a solid back, and sides with a mid rail. The front stays open, so a pallet or a stack of cartons goes in straight from the landing without a gate to hold open.
Three falls, three pick-up points
Three chains come down from the head of the frame onto the cage, so the carriage is pulled at three points rather than one. A load sitting to one side of the plate does not tip the cage or jam it against the posts.

Sheaves at the head of the frame
The chains pass over three sheaves mounted on the cross member at the top of the frame. The sheaves are above the highest stop, so the chain runs straight down to the cage through the whole travel.
The carriage runs inside the posts
The carrier is held between the two posts and runs up inside them, so the cage cannot swing out at height. The posts are the guide — there is no separate mast or rail to line up on site.

Cylinder up the middle, power unit at the foot
The cylinder stands between the posts and pushes the carriage from below. The power unit — motor, pump and oil tank — sits at the foot of the frame with its hose, so the oil level and the motor are checked at floor level.
Floor plates, bolted down
The base frame has plates at the corners that are drilled and bolted to a sound floor. That is the whole foundation: no pit, no shaft walls, and the lift can be unbolted and moved if the layout changes.
Warehouse backs, workshops and yards
For a fixed point where goods change level and a forklift or a stair will not do the job: the lift takes the footprint of its base frame and nothing else.
- Warehouse and stockroomPallets and cartons go from the ground floor to a mezzanine or a first-floor store, loaded through the open front of the cage at both ends.
- Workshop and plant roomParts, crates and drums go up to a service floor, on a cage that holds the load inside while it travels and lands level with the floor.
- Shop and trade counterDeliveries come in at the back and go up to the stockroom above, instead of being carried up the stairs a box at a time.
- Yard and loading bayGoods go from a yard up to a raised loading platform or a first-floor door, on a lift that stands outdoors on its own base.
Custom options on this goods lift
The 3 m build is standard. A taller frame, a wider cage or another colour is made on the same posts and cylinder.

- Lifting height3 m is standard. A taller frame for a full storey, or a shorter one for a half-landing, is built to the floor-to-floor height you send.
- Cage sizeThe carrier is made to the load: wider and deeper for a pallet, lower for cartons through a doorway. Tell us the largest thing you have to lift and we size the cage around it.
- ColourBlue as standard. Any other colour is matched when you order, and your logo can be applied before the machine leaves the factory.
- LandingThe cage lands level with the floor at both ends, so goods are slid on and off. A lip or a short ramp at the lower landing is added to order if the floor is not level.
Freight is quoted separately and confirmed before dispatch
We ship worldwide by sea (LCL and FCL) and by air or express for sample orders. Freight is priced per destination because it depends on port, weight and volume — about 200 kg of machine travels as frame, cage and power unit in one crate.
-
You place the order online
Your order is recorded and the machine is reserved for you while the freight is quoted.
-
We send a freight quote in 24–48 hours
Priced to your nearest port, with transit time, or to your door as DDP if you prefer.
-
You confirm and pay the freight
One invoice for the shipping cost. Nothing is dispatched until you approve it.
-
We book, load and send documents
Packing list, commercial invoice and bill of lading go to your email, with photos of the packed goods.
Frequently asked questions
How does it lift — chain or cylinder?
How much does it carry?
Does it need a shaft or a pit?
Where do the motor and the oil go?
What power supply does it need?
Can it be used outdoors?
Can people ride in the cage?
What does it cost, and how is freight worked out?
For fixed lifting installations used in general industry, see OSHA 29 CFR 1910.176 on materials handling and storage.







Reviews
There are no reviews yet.