Knowing how to choose an aerial lift by height and capacity saves more money than any negotiation on price. Two numbers decide whether the machine can do the job: the height of the work point and the weight that has to be carried to it. Buy on height alone and the platform will be too small for the tools. Buy on capacity alone and the machine will be too heavy for the slab. This guide works through both measurements, then adds the specifications that decide whether the machine can actually reach the work.
Understand working height
Working height is usually defined as platform height plus an assumed operator reach. The value of that assumed reach can differ between manufacturers, and it is not the same as the height a person can comfortably work at with both hands.
Measure the real work point instead. Take the elevation of the highest fixing, fixture or surface and record how it is accessed. A ceiling light needs a hand at the diffuser. A steel connection needs two hands and a wrench. A facade panel needs reach beyond the wall face. Those are three different numbers for the same building.
Record the measurement from the floor the machine will stand on, not from the ground floor. A platform working on a mezzanine has its own base level, and the machine’s own height still has to fit under whatever is above it.
Platform height versus working height
The difference between the two figures is the reason catalogues can look optimistic. A machine with 10 m platform height is often described as offering around 12 m working height. That extra reach belongs to a standing person, not to the platform.
| Figure | What it measures | How to use it |
|---|---|---|
| Platform height | Floor of the platform above the ground | Compare machines on the same basis |
| Working height | Platform height plus assumed operator reach | Marketing figure; confirm the definition used |
| Guardrail height | Top rail above the platform floor | Affects clearance under low structures |
| Stowed height | Machine height when folded | Decides whether it passes a doorway or duct |
Always ask which definition the supplier is quoting. Two machines with the same working height can differ by half a meter of platform height, and that difference may decide whether the job needs an extension deck.
Separate vertical height from outreach
A lift can reach a high point vertically and still fail to reach the work. If the work point is set back from the machine position, horizontal outreach decides the machine, not height.
Boom lifts should be compared on outreach, up-and-over clearance and articulation. A scissor lift is chosen for vertical access over a stable footprint. It does not provide the same side reach, and it should not be pushed into that role.
Sketch the section, not the plan. On paper, mark the machine position, the work point, the vertical rise and the horizontal distance between them. The sketch exposes the cases where a boom is mandatory and where a scissor lift is enough. It also shows whether the machine can stand close enough to the wall in the first place.
Calculate platform capacity
Capacity includes people, tools, materials and approved attachments. It is a working limit, not a cargo rating. Build the load list before comparing models:
- Occupants at working weight, including PPE and tool belts
- Tool boxes, fixing kits, sealant, grinders and vacuums
- Materials carried for installation, such as panels, duct or glazing
- Approved accessories bolted to the platform or the guardrail
Then check how the rating is distributed. Some machines have a separate, lower limit for the extension deck. Others reduce the allowed load when the deck is extended, even though the main platform figure stays the same. Read both figures before planning the work.
Keep a margin for the process, not just for the load. A platform loaded to its exact limit leaves no room for a second trip with a spare part, and that is how overloading starts.
A worked example
Suppose a warehouse needs a sprinkler head replaced at 7.2 m above the floor. The technician weighs 85 kg and carries a 15 kg tool bag. The nearest safe machine position is directly below the head, on a clear aisle 1.9 m wide.
| Item | Value | Effect on choice |
|---|---|---|
| Work point height | 7.2 m | Needs a platform around 5.7 m plus operator reach |
| Offset from machine position | 0 m | Vertical access is enough, so a scissor lift is possible |
| Load | 100 kg plus tools | Most two-person platforms cover it with margin |
| Aisle width | 1.9 m | Decides the maximum machine width, not the height |
| Overhead clearance | Rack beams at 8.1 m | Platform plus guardrail must stay below the beams |
In that case the aisle width, not the height, picks the machine. A platform that reaches 7.2 m but does not fit a 1.9 m aisle is the wrong answer. This is why the measurement list has to include the route.
Our self-propelled scissor lift platform shows how platform height, capacity and machine width are quoted together on a real specification. Compare those three figures against your own numbers, not against the tallest model in the range.
Consider frequency and travel
A lift used once a month can be rented. A lift used every shift has to be easy to drive, easy to position and quick to charge. Frequency changes the specification more than most buyers expect.
- Short access jobs favour a compact machine that moves quickly between points
- Long tasks favour a larger deck that carries tools and material in one trip
- Long routes favour battery capacity and travel speed
- Multiple levels require a machine that can be transported between floors
Also check door widths, turning areas, floor loading and transport dimensions. A machine that is perfect at the work point but cannot enter the building is not a solution.
Read the specification sheet
Put the candidates side by side and compare the same rows. A single table removes most of the ambiguity in a quotation.
| Specification | Why it matters |
|---|---|
| Platform height and working height | Reach to the work point |
| Horizontal outreach | Access to offset work |
| Rated capacity and deck limit | People, tools and materials |
| Machine width and length | Aisle, door and transport fit |
| Turning radius | Positioning in tight areas |
| Gradeability | Ramps and sloped floors |
| Weight and floor loading | Mezzanines and suspended slabs |
| Power source and charging | Indoor use and shift length |
| Stowed height | Doorways and overhead services |
Where a figure is missing, ask for it in writing. A quotation that leaves out machine width or floor loading is incomplete, not concise. The International Powered Access Federation also publishes guidance on matching a machine category to the task.
Four common buying mistakes
- Choosing the tallest machine in the range instead of the smallest one that covers the job
- Using working height from a brochure without checking the platform height behind it
- Ignoring outreach until the machine arrives on site and cannot reach the wall
- Planning capacity for one person when the task needs two plus material
Each of those mistakes has the same cost: a machine that is technically in working order and practically useless. The measurements in this guide exist to prevent that outcome.
How to choose an aerial lift in five steps
The sequence matters as much as the numbers. Work through it in order and the machine selection becomes a short list instead of a range.
- Measure the height of the work point from the floor the machine will stand on.
- Mark the horizontal offset between that work point and the nearest safe machine position.
- List the load: occupants, tools, material and approved accessories.
- Measure the narrowest point on the route: aisle, door, overhead clearance and slab rating.
- Compare specification sheets on those rows, and choose the smallest machine that passes all four checks.
When two models pass, compare weekly cost and travel time rather than headline reach. That is where most of the difference sits once the work is under way. Knowing how to choose an aerial lift is really knowing which of the four checks is tightest, because that check decides the machine.
Conclusion
Height and capacity are the two numbers that decide whether an aerial lift can do the work. Height comes in two forms, working and platform, and outreach decides whether either of them is usable. Capacity covers people, tools and material, with a margin for the process.
Measure the work point, sketch the section, write the load list, then compare specification sheets on the same rows. Buyers who follow that order usually choose a smaller machine than they first expected, and it does the job.
Tell us the work point height, the offset distance and what has to be carried on the platform. We will confirm the platform height and capacity that covers it.
Frequently asked questions
Is working height the same as platform height?
No. Working height usually includes platform height plus an assumed operator reach, and the assumption varies by manufacturer. Compare machines on platform height, then confirm the working height definition in the specification sheet.
Why is horizontal outreach important?
A lift may reach the required elevation and still fail to reach a work point set back from the machine. Outreach, articulation and up-and-over clearance decide whether a boom lift can position the basket where the work is.
What counts toward platform capacity?
Workers, tools, materials, spare parts and approved attachments all count toward the rated capacity. Any extension deck may have its own lower limit, which should be checked separately.
Does an extension deck change the allowed load?
It can. Some machines have separate limits for the main platform and the extension deck, and the allowed load may fall when the deck is extended. Read both figures before planning the task.
Should buyers choose the tallest available lift?
The tallest model is rarely the most efficient. Choose the smallest machine that meets the full height and capacity requirement while fitting the aisle, the door and the floor. A larger machine costs more to move and is harder to position.
What other specifications should be compared?
Compare width, turning radius, overall weight, gradeability, power source, transport dimensions, platform size and capacity. Those figures decide whether the machine can reach the work point and whether it can get there at all.